Service mode TV SHARP

Kumpulan macam-macam cara Service Mode TV Sharp

Cara.1 (model lama)
Cari sebuah switch NORMAL - SERVICE Bentuknya mirip switch yang digunakan pada bagian vertikal. Lokasi ada pada main-pcb bagian belakang dekat dengan TUNER. Untuk masuk service mode - pindah ke posisi SERVICE

Cara.2
Power on Pastikan adjustment gambar pada posisi NORMAL (dengan remot) Short-kan JA137 & JA138 sekitar 1 detik kemudian lepas lagi, maka akan masuk pada service mode. Navigasi menggunakan Ch dan Vol. Untuk exit matikan pesawat.

Ganti IC memori baru (kosong) Power off Short-kan terus sementara JA137 dan JA138. Hidupkan pesawat Tunggu sekitar 30 detik, otomatis data default kan ditulis kedalam memori

Cara.3
Main-switch off atau cabut power-cord (kabel listrik)
Tekan dan tahan secara bersamaan Vol-down dan Ch-up pada front panel, Hidupkan pesawat Navigasi menggunakan Ch dan Vol dengan remote. Exit matikan main-switch (data disimpan secara otomatis)

Cara.4 (slim dengan UOC kotak)
Power on Pastikan adjustment gambar pada posisi NORMAL (dengan remote) Shortkan pin-5 Mikrokontrol sekitar 1 detik dan lepas kembali (atau JA483 dengan JA484) Tekan MENU untuk memilih MODE yang akan diadjust (Adjust Mode, Check mode, Option mode dll) Navigasi menggunakan Ch dan Vol Tunggu sekitar 4 detik sebelum pindah ke adjustment lainnya agar data disimpan dahulu secara otomatis.
Ganti memori baru (kosong) Power off Shortkan terus sementara pin-5 Mikrokontrol ke ground (atau JA483 dengan JA484). Hidupkan pesawat, Tunggu sekitar 30 detik dan otomatis data default akan ditulis kedalam memori. Jika data default gagal - kemungkinan dapat disebabkan karena ABL brigtness terlalu terang atau ada problem pada ABL

Cara.5
Tekan MENU pada remote Selanjutnya tekan angka 4-7-2-5 Navigasi menggunakan Ch dan Vol. Untuk exit matikan pesawat.

Cara.6
» Matikan TV
» Tekan dan tahan {VOL-} & {CH+}.
» Sementara memegang tombol di atas, nyalakan TV.
» TV akan menyala dengan Menu Layanan ditampilkan.
» Ada 5 menu kategori: Deflection - Signal - Feature - Fix Value - EEPROM
» Gunakan {CH+} {CH-} untuk pilih kategori.
Catatan: Tidak semua model akan memiliki 5 kategori. Beberapa akan melompat ke kategori 'Sinyal'.
» Gunakan {VOL+} untuk masuk kategori.
» Gunakan {CH+} {CH-} untuk memilih item yang akan disesuaikan.
» Gunakan {VOL+} {VOL-} untuk menyesuaikan nilai.
» Turn off untuk keluar Menu Layanan.
LCD TV:
» Sementara LCD aktif, cabut kabel power.
» Kemudian sambil menekan {INPUT} & {VOL-} pada remote, pasang kabel listrik kembali ke stopkontak
» Anda akan melihat sedikit "k" muncul dalam tanda kurung.
» Kemudian pada TV, tekan dan tahan {VOL-} & {CH-} dan lepaskan.
» Layanan Menu akan ditampilkan.
» Gunakan {CH+} {CH-} navigasi
» Gunakan {VOL+} {VOL-} untuk menyesuaikan nilai.
» Matikan untuk keluar Menu Layanan.
Proyektor:
» Tekan {INPUT} {UP} {ENTER} {BAWAH} {ENTER} {MENU} di bagian belakang proyektor.
» Sekarang gunakan remote control untuk menavigasi menu.
» Untuk keluar dari Menu Layanan: Tekan {INPUT} {UP} {ENTER} {BAWAH} {ENTER} {MENU} lagi di bagian belakang proyektor.

Continue Reading...

Overcoming The No Exit Image Monitor

Already this week I did not use a PC (Personal Computer) because the monitor can not flame. Lamp Power ON the monitor does orange.Lalu color if the problem is I try to check the monitor cables or in VGAnya a way plugging the monitor cable to the VGA connector to another computer. And it turned out the picture. Means the problem is on my computer VGA (NVIDIA G-Force). Next day I try to check VGAnya. Initial allegation may be due to dirty socket. This time experience computer services have a friend first. And it turned out REALLY dirty ... socket. I freelance cardnya VGA, then I clean them with a screwdriver on the copper ribbons, then I put it to the motherboard and finally the flame as well.
So if your friends have a problem with computers that can not be a flame, try deh check first by using another computer if the monitor can exit the picture what ga. If not out, meaning the problem is likely due to the VGA cardnya dirty and need cleaning. How to clean scratched enough disposable-razor blade or cutter scratch on the copper plate that is connected to the motherboard socket. Then plug it in again and On his computer.
Good luck .............

Continue Reading...

Maxtor hard drive repair

Make you a headache the same hard drive suddenly 'died', hmm do not get confused and do well in the glue aka .. Kasian he3x thrown his taxable if your friends can nutmeg bruised tuh: p, try to check the physical disk, if there is a problem kira2 ga / The following defects have tips on how to improve recall Maxtor hard drive models only: 2b02h1, chipset: dsp, board: athens ata2-plus, code: wah21pb0, if different from his own responsibility would screw up firmware broken alias added ..! jreeeeeeng ..! (Really scary c) he3x, yup i managed to not be afraid ga ko, mending a try anyway dibenerin ga didiemin also remain unused and damaged the following way
1.Download software Salvation can search on google full.nya version can fix all kinds of hard drive I use a free here
2.burn Salvation to cd software
3.pasang hard drive on the primaries, do not forget the jumper to save mode
4.boot using cd Salvation
5.repair it hard use wizard menu just let me no wrong

congratulations your hard drive can be reused

good luck

Continue Reading...

Computer monitor blurred images, out of focus

Computer monitor blurred images, text hard to read. This happens because
1. Which are not appropriate focus Stelan
2. Crt tube conditions who have less good
Step-2 improvement
1. Stel focus: namely direct focus setting by focusing potensio reply was in flaybak. There are computer monitors that use a focus setting but there is also a distinguished using 2 focus setting depending on the model. It did not work?
2. Check the current focus (only for you who already have the basic techniques of electronic repair tv & computer monitors), ie, with focus on how to remove the cable into the socket yg crt, crt tube located behind dimodul, cable ends and then brought near the focus off the chassis with think-2 with a distance of 0 , 5 s / d 1 cm, so the monitor is turned on. focus which would normally generate sparks, the size can dirobah through potensio focus. (this act shall be very careful dangerous-2)
3. If the focus was good put it back in the socket now try to measure voltage Hitler / filamenya, try raising the voltage of filaments between 1-2 vol only. Due to the high terlau filament voltage can cause fijamen tsb crt tube end & dead. How can memjemper resistor bridge with filaments or with filament + cut his lines and then add 1 or 2 rolls of small wires to the ferrite flaybak dilitkan reply. Then again stel
Good luck .........

Continue Reading...

How to Fix Epson Printer T10 T11 T20 Blinking

In this session I will try to explain about the Epson printers that crashed T10 T11 T20 blinking, and visible light on printer flashing between red and green lights alternately (Blinking), it was a sign of your level waste ink is full and ask to reset.
Well to my friend who has a blinking printer need not worry because there is a practical software to reset the printer pal namely: Epson T11 reseter. This software might be for other types of Epson printers, and new writers trying to printers epson T10 T11 and T20.
To get Epson T11 software reseter please Download HERE

The steps for using it are:

1 Extract Files Using Winzip or Winrar
2 Double-click Loader.exe (Ingat!! Do not click AdjProg.exe) if not the program will not work.



3 Click Accept, and will look like the image below




4 Click Select To select the printer type, choose Auto Selection, or Select USBxxx (author select the Auto selection) Then Click OK



5 Click Particular adjustment mode



6 Find a writing pad Waste Ink Counter



7 Click OK and will appear as shown below




8 Click Check to check the Main Counter pad, wait a while, will come out number pad on the main counter and plate Pad.



9 Click the Initialization, wait a while because the software was reset waste ink you, turn off the printer when prompted, and then click Ok




10 Turn the printer back pal.
11 Click Finish, your printer has now been reset.
And see the results my friend printer is back to normal.

Warning: Resetlah Printer Epson T10 T20 T11 you now truly in an error condition (blink-blink)
Do not reset your Epson T10 T11 T20 while still in a state Normal!

Useful Hopefully .....

Continue Reading...

Treatment & USE Solder Tips

In this article we provide maintenance tips and proper use of solder, and aim to obtain effective results in the soldering of electronic components. If you do not already have experience using the solder, then we recommend you to practice soldering techniques on a few simple components (protoboard), before experimenting with a more complicated circuit. This will help you to avoid the risk of damage to the component when you begin to learn soldering.
This basic skills most needed to assemble an electronic circuit starts from the solder. It takes some practice to make perfect, but, like riding a bicycle, once learned is never forgotten! The idea is simple: soldering function to join several components in accordance with the schematic. Various models of solder is sold in electronics stores.

TO OBSERVE ELECTIONS IN solder

VOLTAGE:
Voltage solder most often found in the market is in 220-240V/AC. However, there is also a type of solder low voltage (eg 12V or 24V) Solder was designed with a special controller, the goal is to minimize leakage current, low voltage soldering so with a lower risk of component damage due to leakage current. Low voltage soldering is suitable for use on components that have a high sensitivity, eg IC, TRANSISTOR.
WATTS: Solder has a power rating between 15-500 watts, adjust to the work you do.
TEMPERATURE: simple and inexpensive type of solder do not have the form of temperature regulation. In the solder that has a temperature setting digital temperature readings there, and will have a button control to allow you to vary the temperature setting.

Here is how to make perfect soldering:

1.All components to be soldered must be clean and free from dirt and oil.
2.Position the solder in a safe place.
3.Dip the tip of solder in the solder paste and then ersihkan hot tip with a sponge.
4.At the time of soldering the components on the PCB do a quick two or three seconds at most, because if too long will damage the PCB board or component.
5.Do not move parts soldered to the tin to harden.
6.Clean the rest of the remaining tin on the PCB board with a brush.

Continue Reading...

Analyzing Hp Power Supply Using

In the world of mobile technicians, there are other ways you can do to make the detection of damage to your phone by using a device called a DC Power Supply. DC power supply is extremely helpful to know the voltage generated by mobile phones in general in order to detect the damage and can also replace the function of the battery and battery charging. Please note that each different brand of cell phone - different Amphere generated, so must often use and record the results given amperage.

How to use DC power supply
Ø Turn on DC power supply by pressing the On switch
Ø Position the needle in the column voltage (V) at 3.6 to 4 volts (Under Voltage Battry)

Ø red wire = positive
Cable Ø black = negative
Ø cable green / blue = Btemp (battery temperature)
Cable Ø yellow = BSI (Battery System information)...

Ø Place the red wire to the positive connector on the mobile phone battery
Ø Place the black wire to the negative battery connector on your phone
Ø Then press the switch on the phone

Ø Note the needle on Ampere column, what is produced? (via this column will be analyzed ampere damage, whether the cause software or hardware)

Continue Reading...

Tutorials CRT Monitor For TV

How to change the configuration of yooke CRT monitor to be used in conjunction with aircraft engine TV. Why should the fox first? because the resistance value is very low yooke horizontal monitor, start-0 0.2 ohm, 6 ohm to value may be in charge to a horizontal deflection circuit of a TV set, 0.6 ohm-1, 8 ohms. As a result the load transistor Horizontal become very heavy so can cause damage directly. This time I will try to give a little information about how to change it.  
What should you prepare is. Monitor 
1.CRT complete with yooke. TV engine 2.Modul pinchussion or have facilities for model 21 "and more. 3.Trapo yooke (for SVGA monitor or monitors Flat) 4.Elektronik tool (solder, tin, etc.)
First you need to do is, pay attention to the composition of the horizontal cabling yooke, usually there are additional series in the yooke monitors (set of dynamic convergence and pincushion circuit.) Change the horizontal part of this arrangement which was originally set up in parallel to the composition seri.Dengan way off all connection points in each terminal yooke horizontal (vertical section need not be changed). Discard / disconnect all wiring from the additional circuit (pincushion) is, take the ends of the cable spool core of the horizontal rolls, and you'll get four tip line / cable of this horizontal section, two left and two right. Measure with AVO meter to indicate each coil (coil A and coil B). Connect the coil A coil end side kirike B Right side. And the rest of the two ends that are not in connection to the terminal point is that we will use next. The first process is finished. Next you quickly measure the resistance value of the horizontal yooke we have a fox before, whether it has been quite the range of 0.6 to 0.8 ohm with AVO meter precision (accurate digital meters recommended by the AVO). if it is quite ready for use.

Some conditions that pelu note is: Never try to alter or revoke the static convergence bracelet components in CRT neck, because if you have changed your day even more mungkinperlu
to reset the position that has been set in this factory.
This setting is very critical to a CRT monitor because the pixel number for more than a CRT TV, And for that reason I recommend using machines that have facilities TV settings
pinchusion / degree of curvature side of the picture. (character there are two manual trimpot near vertical IC engine TV).
If the size of the horizontal yooke resistance is still too low (at yooke SVGA monitor or yooke monitor 17 "and above or yooke monitors Flat).
We need to use additional components, namely travo yooke wansonic (specially made by the factory wansonic for use by makers of the TV assembly), this trapo many encountered in the market along with the TV machine wansonic.
How to use the transformer yooke are as follows:
1.Hubungkan blue cable TV to the foot of the machine number 1 transformer also go directly to one terminal yooke horizontal.
2.Hubungkan red cable from the TV machine to the last point (pin6 and pin7) from the foot of the transformer.
3.Hubungkan red wire from yooke to one pin on trapo yooke (pin4, 5,6,7) to adjust the width of the image.

Continue Reading...

CD-ROM Service

Image and video hosting by TinyPicTidak all CD-ROM problems caused by the driver itself, many problems originating from the CDs that are used. Here are Many diagnostic that must be examined before considering the more serious problems. Disc Not Detected. Is the main indication to estimate whether the CD-ROM to function or not. To see if the drive can read CD, insert the CD and see the flame (LED) small front drive. LED light blink a few times indicating that the CD works. If the light does not exist, then chances are the drive can not read the CD-ROM. (But it could have damaged the LED, so no lights). Can also check the status of the disk in Windows 98 and Windows NT by double-click the My Computer icon, the possibility of programs that communicate the CD-ROM drive and Windows does not work properly. But if the CD-ROM drive appears, double-click the icon. If you see an error message, the drive can not read the disc properly. Use the following insruksi for handling the problem.
[1]. One Insert the CD. Error insert the CD-ROM is a dick so probel umum.Meletakkan mold side is always on top. On most drives, you need to concentrate the CD in the indentation on the drive tray. For some drives, especially notebook computers-pressing need to correct a hole in the center of the CD-ROM through the circle on the drive tray.
[2]. CD Gross. Disks are always coated scratch, hands, dust or other substances will not work properly, because the dirt will interfere with the reading of the drive mechanism. Dirty or scratched disc will not work perfectly, although it can not be uniform. You can clean the CD with a clean dry cloth. If you expect dirt caused by the problem of CD-ROM drive, try inserting the disk that the disk berbeda.Adakalanya imperfect curved and thus causing no work at all.
[3]. CD Not Available. If the drive is showing disk read correctly, but can not access data, check the disk is inserted in drive.Bisa so either insert the CD, for example, insert an audio CD while you mean the CD program.
[4]. Autoplay disabled. By default, Windows automatically runs when you insert the CD into the CD-ROM. If the CD does not automatically start, could be detting aotuplay dead. Click Start, Settings, Control Panel. Double-click the system icon Click the Device Manager, and the plus sign icon (+) on CD-ROM option left. Select CD-ROM Drive, click the Properties button. Click the Auto Insert Notification city. Click the OK button on the second window that opens. Restart the computer to access the settings baru.Untuk some CD-ROM may still not start automatically. You can run the CD in the elderly that is double-click the drive icon in My Computer, then double click the program file is needed.
[5]. Software problem. CD-ROM software problem usually starts with the drivers. If the driver becomes damaged (corrupted) or by being accidentally erased, the window can not communicate with the drive. This causes the CD-ROM can not be operated. You can check the status of the driver with double-click System icon in Control Panel. Click the plus sign (+) next to CD-ROM option. If you have a driver that is corrupt, you'll see a yellow triangle with potential Exclamation next to the drive. If the CD-ROM does not work because the drive is bad, to reinstall the drive becomes complicated, because most new computer drives are stored on CD-ROM. If using Win 98, you boot your PC using the startup floppy. Can choose an option to run a computer with CD-ROM support. Win98 will then load the basic drivers for CD ROM drives, which provide access to the drive. Insert the installation CD-ROM and load the Win 98 CD-ROM drivers from the disk.
[6]. Problem Hardware CD-ROM. Unfortunately, we rarely can handle alone most of the problems of CD-ROM hardware. Not easy to fix the components in the drive. If your drive bokar, so you can not get a warranty. When facing a hardware problem, it is better taken to a handyman service that is more aware of the damage. Here are some hardware problems which could possibly occur.
[1]. Less Good perfomance. Some components in the CD-ROM drive can be damaged, because the performance is not reliable. If you sometimes have to insert the CD two or more times before the system read, you can deal with little problems. Smoke or dirt that coats the lens or prism in the drive, cause unfavorable perfomance. Part worn disc player, causing the disk spinning slowly. Most of the CD-ROM disk in place gripping combination with a magnetic rubber ring. If the circle rubber coated by dust or dirt, then grip the disc can not be quite tight, causing the slip when the disk spinning and the drive will not be able to read properly.
[2]. Component Failure. If the drive is a bit "confused" response, it may be a connection or a power cable to the computer having problems. To examine this problem open the PC's case, make sure all the connections a CD-ROM to board sircuit installed properly.
[3]. New Drive Letter. If you install a second hard drive or partition the existing hard drive, marking a drive letter to CD-ROM drive letter in length. Mereinsatall need these programs.
[4]. Drive Can not Open / Close. Bend or break the CD-ROM drive tray, can solve the shut down process is not smooth or does not work at all. If membeturkan drive tray when opened. Could cause the tray is locked and can not be closed. To prevent this, always keep the CD-ROM tray to remain closed when not in use to swap the disc (closed tray also reduces the chance of dirt entering the part in the drive). On some computers, the button that controls the CD-ROM tray can be in one panel with two buttons on the panel exterior. If the outer button is worn out and could not longer open the drive tray by inserting a pin or a piece of paper in a small hole in the face of the CD-ROM drive. If the tray does not close, make sure there is not nothing that prop tray, such as inserting the disc incorrectly. Do not give hard pressure when closing the driver CD-ROM tray and avoid closing the tray when the computer is off, can damage the components inside the drive. Drive tray should be covered with a soft pressure ...
Hopefully Useful ...........

Continue Reading...

Tutorials Service Power Supply

Computer Power Supply is the main power source that provides voltage + 12V,-12V, + 5V,-5V, and the signal POR (Power On Reset) to activate the motherboard. Maximum power that can be consumed by the power supply is about 200 watts with input voltage of 220 V AC from PLN. With a very high efficiency power supply is about 200 watts to provide a voltage of + 5V with a current of about 15-20 A for the purposes of digital equipment motherboards, disk drives, hard disk, processor fan, CD-Rom Drive and what cards are aimed at motherboard slots.
When the load power supply is excessive, then the computer will not walk or can walk but not normal especially when electricity is needed to increase up to the limit. The damage that often occurs is due to overload, unstable voltage, which is not good ground system, and other causes. The most fatal disorders for for power supply voltage is when no issue at all, despite being given a voltage in accordance with needs. Practical ways to improve the computer's power supply could be made as follows:
[1]. Disconnect the power supply box for easier checking of Cassing electronic circuits and disconnect all cables from other tools. Open the power supply box, checking physical electronic components, perhaps there is a fire can be known.
[2]. Check the insert FUSE 220V AC external power source, disconnect it from the socket FUSE and measure the safety wire ties with ohm-meter at the position X1. Ohm-meter needle should indicate a value of about 0 ohms, which means that FUSE is still good. If the ohm-meter shows the number of infinite, then FUSE has been broken, should be replaced new. Do not make the connection wire on FUSE that had broken, because the melting current limit will probably be larger and will cause damage to other parts.
[3]. If FUSE either new or have been replaced but still can not exclude the DC voltage, then proceed to examine the switching power transistor 2SC3039 (two pieces), which served as the control of a PWM power supply. Remove the two 2SC3039 transistor from the PCB and do check the condition of each one with a multimeter. If one transistor is damaged to replace them should they be replaced with a new transistor, for secure and symmetrical characteristics, the imbalance is characteristic of the two transistors causing a disturbance voltage stability issued DC power supply.
[4]. Remove the diode brigde or four pieces of direct diode rectifiers AC power leveling on the insert, check the condition of this diode with a multimeter. Sometimes this was one of the diode leakage or short-circuit, so that the AC power coming in to the circuit switching and disabling the power supply as a whole will follow the power transistor is damaged, fire. Even if this diode leakage rate is very large, it will melt the switching transformer, wire peeled off, and connect short, this is the most fatal damage.
[5]. Also check transistor pulse generator "power on reset", also contained kapasisitor and resistors in the circuit of the transistor base. If the transistor circuit is working properly, then the entire DC voltage regulation will result in reset by the PWM generator and consequently does not issue a DC power supply at all. Replace the new transistor if the transistor POR testing proved defective. So, when the capacitor in the test will be dry, its value changes, the new must be replaced with the exact same value as before.
[6]. Because the computer power supply generally work with higher temperature than room temperature, then there is a possibility because of excessive heat caused solderan legs or component cables there is an independent. Check all solderan on PCB Power Supply, better still make sure to do the repair with the way in re-tin solder is softer (thinner, fluxes 60/40). So the cable connection or foot components that may be loosely knit can be guaranteed and generally power supply will be able to work normally again.
[7]. Pengetesannya active component can not be done with a multimeter is ICTL494 who served as a PWM generator to control power transistor switching work. IC is only in the test by comparing to the IC mode at a power supply of other kinds. Use IC sockets suspected broken with comparator IC is still good.
[8]. When the process of inspection and replacement of damaged components have been done as a whole, then try the power supply is turned on by placing the burden of disk drine only. Check if the fan rotates, measuring stress the yellow wire (+12), red (+5), blue (-5), blue (-12), orange (POR) on the black wire (ground). When the parameters of voltage on the cables are correct, turn off the power supply and replace the load with the motherboard or a full load as before, try again.

Continue Reading...

How it Works CRT Monitor

In this session I will try to explain the workings of CRT monitors. CRT MONITOR HOW Electricity from PLN 220v transformed by the power supply into voltage according to the needs of the circuit, among others: 1. horizontal 2. vertical 3. video block 4. ic block the program and the controller 5. etc.. And the power supply is very important because if there is damage in this section, the monitor will not work normally, even to die. Input is from a VGA monitor or other reply. Image signal from the VGA is then received by the circuit and the circuit SYNCRONISASI VIDEO BLOCK HORIZONTAL and VERTICAL. The incoming signal into a video block is a signal of red, green and blue or green Red and Blue, so a series of VIDEO often called RGB block. so this video blocks just to process color only. result of this block is to go to the cathode tube which is also divided into 3 colors: R, G and B. cathode is its function to produce electrons, so each cathode to produce electrons.
Syncronisasi signal vertical and horizontal in the process by rangkain syncronisasi to then be forwarded to
HORIZONTAL and VERTICAL series circuit. sincronisasi circuit function is to process and produce images, so if the signal is missing one of the monitor screen will look like scrambled. so there are two who work for the first part of the monitor turns on and works normally ie
1. block the video and
2. syncronisasi block vertical and horizontal
Then the vertical syncronisasi forwarded to the vertical circuit, here the vertical signal is processed with the major components that function IC VERTICAL yoke moves vertically.
Then the horizontal syncronisasi forwarded to a series of horizontal and horizontal signal here though with the main component that serves to move the horizontal transistor flyback and yoke tube.
Flyback used to produce very high voltage that is about 26 KV, so that electrons from the cathode to the anode tube can shoot the tube so that the image appears. so if the flyback is not working then the electrons will not shoot and the monitor turns off.
Yoke is used to direct the reply generated by the cathode electron tubes for directional well, horizontal yoke to direct electrons toward the horizontal and vertical yoke for directing electrons into the vertical direction, and if both are combined it will shoot electrons to the anode tube evenly and perfectly.
Then the last one is a series of controller / driver circuit which serves to adjust the monitor settings, wide and narrow and high and low brightness.
OK so some explanations about the workings of the monitor .......

Hopefully Useful ......

Continue Reading...

Nokia IC IC Equation

Equation IC Mobile 
For pe-business in the world of service, especially service handhphone HP spare parts or seller. Maybe this can help, for the replacement IC IC Mobile with a list of equations of several types of mobile phone brands,

    IC BLUETOOTH NOKIA 2630 BCM2048 BROACOM
    IC BCM2048 BLUETOOTH NOKIA 2680 SUPERNOVA BROACOM

    Charging IC NOKIA 1110 GLASS 4 FEET SMALL
    Charging IC NOKIA 1200 GLASS 4 FEET SMALL
    Charging IC NOKIA 1600 GLASS 4 FEET SMALL
    Charging IC NOKIA 5200 GLASS 4 FEET SMALL
    Charging IC NOKIA 6120 GLASS 4 FEET SMALL
    Charging IC NOKIA N70 SMALL GLASS 4 FEET

    IC FLASH NOKIA 3125 K5N28168TA
    IC FLASH NOKIA 6020 K5N28168TA
    IC FLASH NOKIA 6225 (K5N28168TA)
    IC FLASH NOKIA 7200 (K5N28168TA)

    IC FLASH NOKIA 3155 DOWN (K8S5615ETA)
    IC FLASH NOKIA 3230 DOWN (K8S5615ETA)
    IC FLASH NOKIA 6155 DOWN (K8S5615ETA)
    IC FLASH NOKIA 6235 DOWN (K8S5615ETA)
    IC FLASH NOKIA 6280 DOWN (K8S5615ETA)
    IC FLASH NOKIA 7610 DOWN (K8S5615ETA)

    NOKIA 7650 RAM IC K4M51163PE HTM
    NOKIA 7650 RAM IC K4M51163PE GLASS
    NOKIA 9500 RAM IC K4M51163PE GLASS

    IC PA NOKIA 3110 4355929
    IC PA NOKIA 5200 4355929
    IC PA NOKIA 6270 4355929
    IC PA NOKIA 6288 4355929
    IC PA NOKIA 6300 4355929

    MMC IC NOKIA 5300 16 FEET HTM
    MMC IC NOKIA 6300 16 FEET HTM
    MMC IC NOKIA 7610 16 FEET HTM

    IC PA NOKIA 3220 (4355787)
    IC PA NOKIA 3230 (4355787)
    IC PA NOKIA 6020 (4355787)
    IC PA NOKIA 6070 (4355787)
    IC PA NOKIA 6170 (4355787)
    IC PA NOKIA 6260 (4355787)
    IC PA NOKIA 7200 (4355787)
    IC PA NOKIA 7260 (4355787)
    IC PA NOKIA 7270 (4355787)
    IC PA NOKIA 7360 (4355787)
    IC PA NOKIA 7610 (4355641)
    IC PA NOKIA 7610 (4355787)
    IC PA NOKIA 9300i (4355787)

    NOKIA 2610 CPU IC UPP4430E 4377401
    NOKIA 2610 CPU IC UPP4430E T4377402
    NOKIA 2626 CPU IC UPP4430E 4377401

    Charging IC NOKIA 1600 centipede 2 FEET (limiter)
    Charging IC NOKIA 2600 centipede 2 FEET (limiter)
    Charging IC NOKIA 6100 centipede 2 FEET (limiter)

    IC PA 5610 4355951 NOKIA BIG
    IC PA GREAT NOKIA 5700 4355951
    IC PA 6120 4355951 NOKIA BIG
    IC PA 6130 4355951 NOKIA BIG
    IC PA GREAT NOKIA N76 4355951
    IC PA GREAT NOKIA N95 4355951

    IC CPU NOKIA 3110 GSM 4377223 RAP
    NOKIA 3250 CPU IC T4377223 RAP
    IC CPU NOKIA 5200 GSM 4377223 RAP
    IC CPU NOKIA 5300 GSM 4377223 RAP
    NOKIA 6131 CPU IC T4377223 RAP
    NOKIA 6133 CPU IC T4377223 RAP
    IC CPU NOKIA 6270 GSM 4377223 RAP
    IC CPU NOKIA 6300 GSM 4377223 RAP
    IC CPU NOKIA 7370 GSM 4377223 RAP

    NOKIA 1100 Renesas IC PA (08130B)
    NOKIA 1100 IC PA Renesas 08133B
    NOKIA 2300 Renesas IC PA (08130B)
    NOKIA 2300 IC PA Renesas 08133B
    NOKIA 2600 Renesas IC PA (08130B)
    NOKIA 2600 IC PA Renesas 08133B

    IC BLUETOOTH NOKIA 5700 BR 1SET
    IC BLUETOOTH NOKIA 6111 BR 1SET
    IC BLUETOOTH NOKIA 6280 BR 1SET
    IC BLUETOOTH NOKIA 6288 BR 1SET
    IC BLUETOOTH NOKIA N70 BR 1SET
    IC BLUETOOTH NOKIA N76 BR 1SET


    IC FLASH NOKIA 6610i 128W18T GLASS
    IC FLASH NOKIA 7650 GLASS 128W18T

    IC RADIO NOKIA 1650 TEA 5760 GLASS
    IC RADIO NOKIA 2626 TEA 5760 GLASS
    IC RADIO NOKIA 3110 TEA 5760 GLASS
    IC RADIO NOKIA 5310 TEA 5760 GLASS
    IC RADIO NOKIA 5700 TEA 5760 GLASS
    IC RADIO NOKIA 6300 TEA 5760 GLASS

    NOKIA 2600 CPU IC clasik UPP8611E 4377461
    NOKIA 2600 CPU IC clasik UPP8611E 4377461
    NOKIA 2600 CPU IC clasik UPP8611E 4377463
    NOKIA 2630 CPU IC UPP8611E 4377461
    NOKIA 2630 CPU IC UPP8611E 4377463
    IC CPU UPP8611E 4377463 NOKIA 2680 SUPERNOVA
    NOKIA 5000 CPU IC UPP8611E 4377461
    NOKIA 5310 CPU IC UPP8611E 4377461

    IC CPU NOKIA 1200 (UPP C2M 4377008
    NOKIA 1208 CPU IC (UPP C2M 4377008
    NOKIA 1650 CPU IC (UPP C2M 4377008

    NOKIA FLASH 1112 NS032 IC SPANSON
    NOKIA FLASH 1200 NS032 IC SPANSON
    NOKIA FLASH 1600 NS032 IC SPANSON
    NOKIA FLASH 2310 NS032 IC SPANSON
    NOKIA FLASH 2600 NS032 IC SPANSON

    IC FLASH NOKIA 2100 (INTEL 1602C3
    IC FLASH NOKIA 3610 (INTEL 1602C3
    IC FLASH NOKIA 8250 (INTEL 1602C3

    NOKIA 3250 IC ANTENNA SWITCH
    NOKIA 6270 IC ANTENNA SWITCH
    IC ANTENNA SWITCH NOKIA N73
    IC ANTENNA SWITCH NOKIA N95

    IC BLUETOOTH NOKIA 5310 BCM2048 BROACOM
    IC BLUETOOTH NOKIA 5610 BCM2048 BROACOM
    IC BLUETOOTH NOKIA 6120 BCM2048 BROACOM
    IC BLUETOOTH NOKIA 7310 BCM2048 BROACOM

    IC FLASH NOKIA 2600 clasik M36L0R805
    IC FLASH NOKIA 2630 M36L0R805
    IC CPU V3.0 NOKIA 6233 RAP3G 4377151
    IC CPU V3.0 NOKIA 6234 RAP3G 4377151
    IC CPU V3.0 NOKIA 6280 RAP3G 4377151
    IC CPU V3.0 NOKIA 6288 RAP3G 4377151

    IC RAM K4M64163PK NOKIA 6235 BLACK
    IC RAM K4M64163PK NOKIA 6600 BLACK
    IC RAM K4M64163PK NOKIA 7610 BLACK
    IC RAM K4M64163PK NOKIA E60 BLACK
    IC RAM K4M64163PK NOKIA N70 BLACK
    IC RAM K4M64163PK NOKIA N71 BLACK
    IC RAM K4M64163PK NOKIA N73 BLACK
    IC RAM K4M64163PK NOKIA N91 BLACK

    IC PA 5610 4355898 NOKIA SMALL
    IC PA 5700 4355898 NOKIA SMALL
    IC PA 6120 4355898 NOKIA SMALL
    NOKIA N76 PA 4355898 IC SMALL
    NOKIA N95 PA 4355898 IC SMALL

    IC FLASH NOKIA 5100 (K5G5629ATD)
    IC FLASH NOKIA 5300 (K5G5629ATD)
    IC FLASH NOKIA 6300 (K5G5629ATD)
    IC FLASH NOKIA 6300 K5G5629ATB

    NOKIA 2100 IC cans PA PF08103B ORI
    NOKIA 3610 IC cans PA PF08103B ORI
    NOKIA 5210 IC cans PA PF08103B ORI
    NOKIA 6210 IC cans PA PF08103B ORI
    NOKIA 8210 IC cans PA PF08103B ORI
    NOKIA 8250 IC cans PA PF08103B ORI
    NOKIA 8850 IC cans PA PF08103B ORI
    NOKIA 8855 IC cans PA PF08103B ORI
    NOKIA 9210 IC cans PA PF08103B ORI

    NOKIA 3110 CAMERA IC ST0984NP
    NOKIA 3110 CAMERA IC XTV0984N
    NOKIA 5300 CAMERA IC X0984NP
    NOKIA 5300 CAMERA IC XTV0984N
    NOKIA 5500 CAMERA IC X0984NP
    NOKIA 5700 CAMERA IC X0984NP
    NOKIA 6120 CAMERA IC ST0984NP
    NOKIA 6130 CAMERA IC ST0984NP
    NOKIA 6265 CAMERA IC STV0984N
    NOKIA 6275 CAMERA IC XTV0984N
    NOKIA 6300 CAMERA IC ST0984NP
    NOKIA 6300 CAMERA IC XTV0984N
    NOKIA N76 CAMERA IC STV0984N

    IC PA NOKIA 6500 (4350297)
    IC PA NOKIA 6510 (4350297)
    IC PA NOKIA 6800 (4350297)
    IC PA NOKIA 7600 (4350297)
    IC PA NOKIA 7650 (4350297)
    IC PA NOKIA 8310 (4350297)
    IC PA NOKIA 8910 (4350297)

    IC BUFFER / RF NOKIA 6630 4380039 HINKU
    IC BUFFER / RF NOKIA 6680 4380039 HINKU
    IC BUFFER / RF NOKIA 7360 4380039 HINKU
    IC BUFFER / RF HINKU GREAT NOKIA N70 4380039
    IC BUFFER / RF NOKIA N71 4380039 HINKU
    IC BUFFER / RF NOKIA N72 4380039 HINKU
    IC BUFFER / RF HINKU GREAT NOKIA N91 4380039

    NOKIA 3100 Renesas IC PA (08125B)
    NOKIA 3120 Renesas IC PA (08125B)
    NOKIA 3650 Renesas IC PA (08125B)
    NOKIA 3660 Renesas IC PA (08125B)
    NOKIA 6100 Renesas IC PA (08125B)
    NOKIA 6600 Renesas IC PA (08125B)
    NOKIA NGAGE Renesas IC PA (08125B)
    NOKIA QD Renesas IC PA (08125B)

    IC POWER SUPPLY NOKIA 2116 4376401 UEM
    IC POWER SUPPLY NOKIA 2126 4376401 UEM
    IC POWER SUPPLY NOKIA 2255 4376401 UEM
    IC POWER SUPPLY NOKIA 2300 4376401 UEM
    IC POWER SUPPLY NOKIA 2600 4376401 UEM
    IC POWER SUPPLY NOKIA 6225 4376401 UEM
    IC POWER SUPPLY NOKIA 6585 4376401 UEM
    UEM IC POWER SUPPLY NOKIA 8310 (4370401)

    UEM IC POWER SUPPLY NOKIA 2112 (4377027)
    UEM IC POWER SUPPLY NOKIA 2600 (4370027)
    UEM IC POWER SUPPLY NOKIA 6016 (4377027)
    UEM IC POWER SUPPLY NOKIA 7710 (4377027)

    IC BUFFER / RF NOKIA 3200 Helga 4380037
    IC BUFFER / RF NOKIA 5100 Helga 4380037
    IC BUFFER / RF NOKIA 7210 Helga 4380037
    IC BUFFER / RF NOKIA 7250 Helga 4380037


    IC BLUETOOTH NOKIA 3650 1 SET 0700079
    IC BLUETOOTH NOKIA 3660 1 SET 0700079
    IC BLUETOOTH NOKIA 6600 1 SET 0700079
    IC BLUETOOTH NOKIA 7600 1 SET 0700079
    IC BLUETOOTH NOKIA NGAGE 1 SET 0700079
    IC BLUETOOTH NOKIA NGAGE QD 1 SET 0700079

    IC CPU NOKIA 3100 UPP8210 4377021
    IC CPU NOKIA 3100 UPP824 4370873
    IC CPU NOKIA 3100 UPPV8210 4370931
    IC CPU NOKIA 3100 UPPV826 4370931
    IC CPU NOKIA 3120 UPPV826 4370931
    IC CPU NOKIA 3300 UPP826 4370931
    IC CPU NOKIA 3530 UPP824 4370873
    IC CPU NOKIA 5100 UPPV8210 4377021
    IC CPU NOKIA 5100 UPPV8241 4370873
    IC CPU NOKIA 6100 UPP824 4370873
    IC CPU NOKIA 6100 UPP826 4370931
    IC CPU NOKIA 6100 UPPV8210 4377021
    IC CPU NOKIA 6108 UPP822 4370873
    IC CPU NOKIA 6108 UPPV8210 4377021
    IC CPU NOKIA 6108 UPPV826 4370931
    IC CPU NOKIA 6610 UPP824 4370873
    IC CPU NOKIA 6610 UPPV8210 4377021
    IC CPU NOKIA 6800 UPP822 4370873
    IC CPU NOKIA 6800 UPPV8210 4377021
    IC CPU NOKIA 7210 UPP824 4370873
    IC CPU NOKIA 7210 UPPV8210 4377021
    IC CPU NOKIA 7250 UPP824 4370873
    IC CPU NOKIA 7250 UPPV8210 4377021

    IC POWER SUPPLY NOKIA 1100 4370825 UEM
    IC POWER SUPPLY NOKIA 3300 4370825 UEM
    IC POWER SUPPLY NOKIA 3510 4370825 UEM
    IC POWER SUPPLY NOKIA 3650 4370825 UEM
    IC POWER SUPPLY NOKIA 5100 4370825 UEM
    IC POWER SUPPLY NOKIA 6108 4370825 UEM
    IC POWER SUPPLY NOKIA 6600 4370825 UEM
    IC POWER SUPPLY NOKIA 6610 4370825 UEM
    IC POWER SUPPLY NOKIA 6610i UEM 4370825
    IC POWER SUPPLY NOKIA 6800 4370825 UEM
    IC POWER SUPPLY NOKIA 7250 4370825 UEM
    IC POWER SUPPLY NOKIA NGAGE QD UEM 4370825
    UEM IC POWER SUPPLY NOKIA 1110 (4376441)
    UEM IC POWER SUPPLY NOKIA 1600 (4376441)
    UEM IC POWER SUPPLY NOKIA 2310 (4376441)
    UEM IC POWER SUPPLY NOKIA 2610 (4376441)
    UEM IC POWER SUPPLY NOKIA 6030 (4376441)

    NOKIA 6280 RAM IC K4M28163PF GLASS
    NOKIA 6600 RAM IC K4M28163PF GLASS
    NOKIA 7610 RAM IC K4M28163PF GLASS
    IC RAM K4M28163PF NOKIA NGAGE CLASSIC GLASS
    IC RAM NOKIA NGAGE QD K4M28163PF GLASS

    IC BUFFER / RF NOKIA 2100 4370781 HAGAR
    IC BUFFER / RF NOKIA 3310 4370781 HAGAR
    IC BUFFER / RF NOKIA 6510 HAGAR
    IC BUFFER / RF NOKIA 6800 HAGAR
    IC BUFFER / RF NOKIA 6810 HAGAR
    IC BUFFER / RF NOKIA 8210 4370781 HAGAR
    IC BUFFER / RF NOKIA 8310 4370781 HAGAR
    IC BUFFER / RF NOKIA 8850 4370781 HAGAR
    IC BUFFER / RF NOKIA 8855 4370781 HAGAR
    IC BUFFER / RF NOKIA 8910 4370781 HAGAR

    NOKIA 6235 RAM IC K4M64163PH GLASS
    NOKIA 6255 RAM IC K4M64163PH GLASS
    NOKIA 6630 RAM IC K4M64163PH GLASS
    NOKIA 6680 RAM IC K4M64163PH GLASS
    IC RAM NOKIA N70 K4M64163PH GLASS
    IC RAM NOKIA N72 K4M64163PH GLASS
    IC RAM NOKIA N91 K4M64163PH GLASS

    NOKIA 1110 CPU IC (UPP220IE) 4377159
    IC CPU NOKIA 1600 (UPP220IE) 4377159
    NOKIA 2310 CPU IC (UPP220IE) 4377159

    IC BUFFER / RF NOKIA 3300 HELGO 4370979
    IC BUFFER / RF NOKIA 6111 HELGO 4370979
    IC BUFFER / RF NOKIA 6220 HELGO 4370979
    IC BUFFER / RF NOKIA 6230 HELGO 4370979
    IC BUFFER / RF NOKIA 6610 HELGO
    IC BUFFER / RF Nokia 6610i HELGO
    IC BUFFER / RF NOKIA 6820 HELGO 4370979
    IC BUFFER / RF NOKIA 7200 HELGO 4370979
    IC BUFFER / RF NOKIA 7600 HELGO 4370979

    NOKIA 3220 IC ANTENNA SWITCH qv
    NOKIA 3230 IC ANTENNA SWITCH qv
    NOKIA 6020 IC ANTENNA SWITCH qv
    NOKIA 6070 IC ANTENNA SWITCH qv
    NOKIA 6101 IC ANTENNA SWITCH qv
    NOKIA 6260 IC ANTENNA SWITCH qv
    NOKIA 7270 IC ANTENNA SWITCH qv
    NOKIA 7360 IC ANTENNA SWITCH qv
    NOKIA 7610 IC ANTENNA SWITCH qv

    IC LIGHT NOKIA 1600 BLACK 8 perforated CENTRAL
    LAMPS IC NOKIA N70 BLACK 8 perforated CENTRAL

    NOKIA 3650 IC ANTENNA SWITCH 1S2E KCT
    NOKIA 3660 IC ANTENNA SWITCH 1S2E KCT
    NOKIA 6510 IC ANTENNA SWITCH 1S2E KCT
    NOKIA 6600 IC ANTENNA SWITCH IS2E KCT
    NOKIA 8310 IC ANTENNA SWITCH 1S2E KCT KCT
    NOKIA 8910 IC ANTENNA SWITCH 1S2E KCT KCT
    IC ANTENNA SWITCH NOKIA NGAGE CLASSIC KCT IS2E

    IC KEYPAD NOKIA E50 25 FOOT GLASS
    Sony Erikson K700 KEYPAD IC 25 FOOT GLASS
    IC LCD NOKIA 2600 25 FOOT GLASS
    IC LCD NOKIA 2650 25 FOOT GLASS
    IC LCD NOKIA 3100 25 FOOT GLASS
    IC LCD NOKIA 3120 25 FOOT GLASS
    IC LCD NOKIA 3200 25 FOOT GLASS
    IC LCD NOKIA 3650 25 FOOT GLASS FET 403
    IC LCD NOKIA 6100 25 FOOT GLASS
    IC LCD NOKIA 6230 25 FOOT GLASS
    IC LCD NOKIA 6288 25 FOOT GLASS FET348
    IC LCD NOKIA 6600 25 FOOT GLASS FET348
    IC LCD NOKIA 6610 25 FOOT GLASS
    Nokia 6610i LCD IC 25 FOOT GLASS
    IC LCD NOKIA 6670 25 FOOT GLASS
    IC LCD NOKIA 7210 25 FOOT GLASS
    IC LCD NOKIA 7250 25 FOOT GLASS
    IC LCD NOKIA 7610 25 FOOT GLASS
    IC LCD NOKIA 8800 25 FOOT GLASS FET348
    IC LCD NOKIA NGAGE KLSK 25 FOOT GLASS
    IC LCD NOKIA 4041 QD 25 FEET PHILIP GLASS

    FLASH IC 3650 AMD 001 NOKIA N643
    FLASH IC 6600 AMD 001 NOKIA N643
    IC FLASH NOKIA 2610 K5U2817ATM
    IC FLASH NOKIA 2626 K5U2817ATM

    IC POWER SUPPLY NOKIA 2865 4376371 UEM
    IC POWER SUPPLY NOKIA 3155 4376371 UEM
    UEM IC POWER SUPPLY NOKIA 3220 (4376371)
    IC POWER SUPPLY NOKIA 3230 4376371 UEM
    IC POWER SUPPLY NOKIA 5070 4376371 UEM
    IC POWER SUPPLY NOKIA 6020 4376371 UEM
    IC POWER SUPPLY NOKIA 6070 4376371 UEM
    IC POWER SUPPLY NOKIA 6080 4376371 UEM
    IC POWER SUPPLY NOKIA 6101 4376371 UEM
    IC POWER SUPPLY NOKIA 6155 4376371 UEM
    UEM IC POWER SUPPLY NOKIA 6230 (4376371)
    IC POWER SUPPLY NOKIA 6230 4370945 UEM
    IC POWER SUPPLY NOKIA 6235 4376371 UEM
    IC POWER SUPPLY NOKIA 6255 4376371 UEM
    IC POWER SUPPLY NOKIA 6260 4376371 UEM
    IC POWER SUPPLY NOKIA 6265 4376371 UEM
    IC POWER SUPPLY NOKIA 7360 4376371 UEM
    IC POWER SUPPLY NOKIA 7600 4370945 UEM
    IC POWER SUPPLY NOKIA 7600 4376371 UEM
    IC POWER SUPPLY NOKIA 7610 4376371 UEM
    IC POWER SUPPLY NOKIA 9300 4376371 UEM

    IC PA NOKIA 3300 (4350383)
    IC PA NOKIA 5100 (4350383)
    IC PA NOKIA 6230 (4350383)
    IC PA NOKIA 6610 (4350383)
    IC PA Nokia 6610i (4350383)
    IC PA NOKIA 7210 (4350383)
    IC PA NOKIA 7250 (4350383)

    NOKIA 3105 CPU IC (UPP V835E) 4375019
    IC CPU NOKIA 3200 (UPP V835E) 4375019
    NOKIA 3220 IC CPU (V835E UPP)
    NOKIA 3220 IC CPU V835E 4371105
    NOKIA 6820 IC CPU (V835E UPP)
    NOKIA 7200 IC CPU (V835E UPP)
    NOKIA 7260 IC CPU (V835E UPP)
Flash IC Nokia 5310/3120 Flash IC Nokia 2330/2323 / NOKIA 6235 RAM IC K4M64163PH GLASS NOKIA 6255 RAM IC K4M64163PH GLASS NOKIA 6630 RAM IC K4M64163PH GLASS NOKIA 6680 RAM IC K4M64163PH GLASS IC RAM NOKIA N70 K4M64163PH GLASS IC RAM NOKIA N72 K4M64163PH GLASS IC RAM NOKIA N91 K4M64163PH GLASS
 
   Hopefully Useful ..........................

Continue Reading...